Vista Home Security System VISTA 20HWSE User Manual

Security  
Security  
System  
System  
User's Manual  
VISTA-20SE/VISTA-20HWSE  
®
N7527V2 6/97  
 
TABLE OF CONTENTS  
SYSTEM OVERVIEW .................................................... 4  
CHIME MODE .............................................................. 23  
PANIC KEYS ............................................................... 24  
USING DEVICE COMMANDS ..................................... 25  
PAGING FEATURE ..................................................... 26  
General ...................................................................... 4  
A Partitioned System................................................ 4  
Zones ........................................................................ 4  
Burglary Protection ................................................. 5  
Security Codes ......................................................... 5  
Fire Protection .......................................................... 6  
Alarms ....................................................................... 6  
Memory of Alarm ...................................................... 6  
Phone Access & Voice Response ........................... 6  
ENTRY/EXIT DELAYS .................................................. 7  
General Information.................................................. 7  
Exit Alarms................................................................ 8  
COMMON ZONE OPERATION ..................................... 8  
SECURITY CODES ..................................................... 27  
General .................................................................... 27  
Babysitter Code ...................................................... 27  
Duress Code ........................................................... 27  
Quick Arming .......................................................... 27  
To Add or Change A User ...................................... 28  
To Delete A User ..................................................... 28  
TESTING THE SYSTEM.............................................. 29  
TROUBLE CONDITIONS ............................................ 31  
FIRE ALARM SYSTEM ............................................... 33  
NFPA RECOMMENDATIONS ..................................... 34  
EMERGENCY EVACUATION...................................... 35  
MAINTAINING YOUR SYSTEM .................................. 36  
QUICK GUIDE TO SYSTEM FUNCTIONS.................. 38  
SUMMARY OF AUDIBLE NOTIFICATION ................. 40  
GLOSSARY ................................................................. 41  
INSURANCE CREDIT REQUEST FORM .................... 47  
INDEX .......................................................................... 50  
ABOUT THE KEYPADS ................................................ 9  
FUNCTIONS OF THE KEYPADS ................................ 12  
CHECKING FOR OPEN ZONES ................................. 14  
ARMING PERIMETER ONLY (STAY)......................... 15  
ARMING PERIMETER ONLY (INSTANT) ................... 16  
ARMING ALL PROTECTION (AWAY)........................ 17  
ARMING ALL PROTECTION (MAXIMUM) ................. 18  
DISARMING AND SILENCING ALARMS ................... 19  
Memory of Alarm .................................................... 20  
BYPASSING PROTECTION ZONES .......................... 21  
Quick Bypass ......................................................... 22  
Displaying Bypassed Zones .................................. 22  
– 3 –  
 
SYSTEM OVERVIEW  
General  
Congratulations on your ownership of an Ademco Partitioned Security System. You've  
made a wise decision in choosing it, for it represents the latest in security protection  
technology today. Ademco is the world's largest manufacturer of security systems and  
millions of premises are protected by Ademco systems.  
This system offers you three forms of protection: burglary, fire and emergency. Your  
system consists of at least one keypad which provides control of system operation,  
and includes various sensors which provide perimeter and interior burglary protection,  
plus smoke or combustion detectors designed to provide early warning in case of fire.  
The system uses microcomputer technology to monitor all protection zones and  
system status, display appropriate information on the keypad(s) used with the system,  
and initiate appropriate alarms. Your system may also have been programmed to  
automatically send alarm or status messages over the phone lines to a central alarm  
monitoring station.  
A Partitioned  
System  
Simply stated, a partitioned system is a single physical alarm system that provides  
independent areas of protection intended for use by independent users. For the most  
part, you need not know about other users and their structure in the system, but from  
time to time, you may see display messages which indicate the system is in use by  
another user. Do not be concerned, this is normal. A partitioned system may also have  
a "common zone" area, which is an area shared by users of both partitions. Refer to  
the COMMON ZONE OPERATION section for details on using this feature.  
Zones  
Your system's sensing devices have been assigned to various "zones." For example,  
the sensing device on your Entry/Exit door may have been assigned to zone 01,  
sensing devices on windows in the master bedroom to zone 02, and so on. These  
numbers will appear on the display, along with a description for that zone (if  
programmed), when an alarm or trouble condition occurs.  
– 4 –  
 
SYSTEM OVERVIEW  
Burglary  
Protection  
Your system provides four modes of burglary protection: STAY, AWAY, INSTANT and  
MAXIMUM, and allows you to BYPASS selected zones while leaving the rest of the  
system armed. You must turn on or "arm" the burglary protection portion of your  
system before it will sense burglary alarms. The system also provides a CHIME mode,  
for alerting users to the opening of protected doors and windows while the system is  
disarmed. Refer to the other sections of this manual for procedures for using these  
features.  
The following table lists the four different arming modes and the results of each.  
Features For Each Arming Mode  
Arming  
Mode  
Exit Delay  
Entry Delay  
Perimeter Armed  
Interior Armed  
AWAY  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
No  
Yes  
Yes  
Yes  
Yes  
Yes  
No  
STAY  
INSTANT  
MAXIMUM  
No  
No  
Yes  
Security Codes  
Fire Protection  
At the time of installation, you were assigned a personal four-digit security code,  
known only to you. You must enter the security code when arming and disarming the  
system, and when performing other system functions. As an additional safety feature,  
other users who do not have a need to know your code can be assigned different  
security codes. Refer to the SECURITY CODES section for procedures on adding  
security codes to the system.  
The fire protection portion of your security system (if used) is always active and will  
sound an alarm if a fire condition is detected. Refer to the FIRE ALARM SYSTEM  
section for important information concerning fire protection, smoke detectors and  
planning emergency exit routes from the premises.  
– 5 –  
 
SYSTEM OVERVIEW  
Alarms  
When an alarm occurs, both the keypad and external sounders will sound, and the  
keypad will display the zone(s) causing the alarm. If your system is connected to a  
central monitoring station, an alarm message will also be sent. To stop the alarm  
sounding, simply disarm the system.  
Memory of Alarm  
When an alarm condition occurs, the keypad displays the number(s) of the zone(s) that  
caused the problem, and displays the type of alarm (ex. FIRE, ALARM). It remains  
displayed until it is cleared by disarming the system (see DISARMING THE SYSTEM  
section).  
Phone Access &  
Voice  
Your system may include a voice module that will permit you to access the system via  
a Touch-tone phone, either on-premises or by call-in when away. The phone access  
feature will enable you to do the following:  
Receive synthesized voice messages over the telephone regarding the status of the  
security system.  
Response  
Capability  
Arm and disarm the system and perform most function commands via the telephone,  
with voice confirmation provided after each command entry.  
Complete information regarding the use of this feature is provided in a separate  
manual entitled PHONE ACCESS USER'S GUIDE, which accompanies the voice  
module.  
Paging Feature  
If the paging feature has been programmed for your system, your pager will respond to  
certain conditions as they occur in your system. Your pager will display code numbers  
indicating the type of condition that has occurred. Refer to the PAGING FEATURE  
section later in this manual for detailed information.  
– 6 –  
 
ENTRY/EXIT DELAYS  
Your system has preset time delays, known as exit delay and entry delay. Whenever  
you arm your system, exit delay gives you time to leave through the designated exit  
door without setting off an alarm. Exit delay begins immediately after entering any  
arming command, and applies to all modes of arming protection. If programmed, a  
slow beeping will sound throughout the exit delay period.  
General  
Information  
Entry Delays give you time to disarm the system when you re-enter through the  
designated entrance door. But you must disarm the system before the entry delay  
period ends, or an alarm will occur. The keypad beeps during the entry delay period,  
reminding you to disarm the system. There are two entry delays (if programmed). The  
first is for your primary entrance and the second can be used for a secondary  
entrance, where a longer delay is required to walk to the keypad to disarm the system.  
You can also arm the system with no entry delay at all by using either INSTANT or  
MAXIMUM arming modes. These modes provide greater security while on the  
premises or while away for extended periods of time.  
See your installer for your delay times.  
Partition 1  
Partition 2  
Exit Delay:  
Exit Delay:  
seconds  
seconds  
Entry Delay 1:  
Entry Delay 2:  
seconds  
seconds  
Entry Delay 1:  
Entry Delay 2:  
seconds  
seconds  
– 7 –  
 
ENTRY/EXIT DELAYS  
Exit Alarms  
Whenever you arm the system, the exit delay begins. If an entry/exit door or interior zone is  
faulted when the exit delay ends (e.g., exit door left open), the system sounds an alarm and  
starts the entry delay timer. If you disarm the system before the entry delay ends, the alarm  
sound stops and the message "CANCELLED ALARM" or "CA" is displayed on the keypad,  
along with a zone number indicating the faulted zone. No message is sent to the alarm  
monitoring company.  
To minimize false alarms  
sent to the alarm  
monitoring company,  
your system may have  
been programmed for  
this feature. Ask your  
installer if "Exit Alarm" is  
active for your system.  
To clear the exit alarm condition, the open zone must be made intact; to clear the display, enter  
your code plus OFF.  
If you do not disarm the system before the entry delay ends, and an entry/exit door or interior  
zone is still open, the alarm sound continues and an "exit alarm" message is sent to the alarm  
monitoring company. The message ""EXIT ALARM" or "EA" is displayed on the keypad, along  
with a zone number indicating the faulted zone. To stop the alarm, the system must be  
disarmed (your code plus OFF); to clear the display, enter your code plus OFF a second time.  
Exit Alarm Active  
An “exit alarm” also results if an entry/exit door or interior zone is faulted within two minutes  
after the end of the exit delay.  
COMMON ZONE OPERATION  
Your system may have been set up to use a common zone, which is an area shared by users of  
both partitions, such as a foyer or lobby. If so, please note the following:  
• The common zone will sound and report alarms only when both partitions are armed. If only  
one partition is armed, the system ignores faults on the common zone.  
• Either partition may arm its system if the common zone is faulted, but once armed, the other  
partition will not be able to arm unless the common zone is first bypassed or the fault is  
corrected.  
Ask your  
installer if a common  
zone was assigned.  
• Faults on the common zone are displayed on keypads in both partitions.  
• Either partition can clear and restore the common zone after an alarm.  
– 8 –  
 
ABOUT THE KEYPADS  
General  
Your keypads allow you to control all system functions. The keypads feature a  
telephone style (digital) keypad and a Liquid Crystal Display (LCD) which shows the  
nature and location of all occurrences.  
IMPORTANT: If the key-  
pad beeps rapidly upon  
entering the premises, it  
indicates that an alarm  
has occurred during  
your absence and an  
intruder may still be on  
the premises. LEAVE  
IMMEDIATELY and  
CONTACT THE POLICE  
The keypads also feature a built-in sounder which will sound during alarms and  
troubles. The keypads also "beep" during certain system functions, such as during  
entry/exit delay times, in CHIME mode, and when depressing any of the keys (to  
acknowledge the key press).  
There are two basic types of keypads – a Fixed-Word keypad and an Alpha key-  
pad (both described below). These keypads are available in two styles, shown as  
style A and style B, either of which may have been used in your system. Although  
different in appearance, both styles are functionally the same. Style B keypads have  
a flip-down cover which can be removed, if desired.  
from  
location.  
a
nearby safe  
2-Line Alpha Keypad  
2-line Alpha keypads feature a 2-line, 32-character alphanumeric LCD which can  
display system messages in friendly English. These keypads can also be  
programmed with custom zone descriptors. The screen displays depicted in this  
manual are those that typically appear on a 2-line Alpha keypad.  
1-Line Alpha Keypad 1-line Alpha keypads feature a 16-character alphanumeric LCD which can display  
system messages in friendly English. Messages are the same as those for 2-line  
Alpha keypads, but are displayed one line at a time. To view the second line of the  
message, simply press the  
or wait 3 seconds.  
#
key. To return to the first line, press the  
#
again,  
After pressing the  
#
key, wait at least 3 seconds before entering a command.  
Fixed-Word Keypad  
Fixed-Word keypads are functionally identical to Alpha keypads, but the LCD display  
uses pre-designated words to identify the nature and location of occurrences.  
– 9 –  
 
ABOUT THE KEYPADS  
ARMED  
READY  
OFF  
AWAY  
2
STAY  
1
3
MAX  
TEST  
BYPASS  
4
5
CODE  
8
6
CHIME  
9
INSTANT  
7
READY  
0
#
*
PANIC  
6139 ALPHA KEYPAD  
AWAY  
STAY  
INSTANT  
BYPASS  
NOT READY  
NO AC  
CHIME  
BAT  
NO AC  
AWAY  
ARMED  
READY  
ARMED  
BYPASS  
00  
NOT READY  
CHIME BAT  
ALARM  
CHECK  
FIRE  
ALARM STAY  
READY  
CHECK INSTANT  
FIRE  
OFF  
AWAY  
2
STAY  
OFF  
AWAY  
STAY  
A
1
3
1
MAX  
2
TEST  
5
3
BYPASS  
6
MAX  
TEST  
BYPASS  
4
INSTANT  
5
CODE  
8
6
CHIME  
9
B
C
4
INSTANT  
CODE  
CHIME  
7
READY  
8
9
7
READY  
0
#
0
PANIC  
#
*
*
PANIC  
6127/6128  
6137  
FIXED-WORD KEYPADS  
– 10 –  
 
ABOUT THE KEYPADS  
Fixed-Word Keypad Displays  
AWAY All burglary zones, interior & perimeter, are  
armed.  
NO AC  
CHIME  
BAT  
AWAY  
STAY  
INSTANT  
BYPASS  
STAY Perimeter burglary zones, such as windows and  
00  
00  
doors are armed.  
ALARM  
CHECK  
FIRE  
INSTANT Perimeter burglary zones armed and entry delay  
NOT READY  
is turned off.  
STYLE A  
BYPASS One or more burglary protection zones have been  
bypassed.  
NOT READY Appears when burglary portion of the system is  
not ready for arming (due to one or more open  
protection zones).  
NO AC  
AWAY  
AWAY  
00  
BYPASS  
NOT READY  
CHIME BAT  
READY The burglary portion of the system is ready to be  
ALARM  
FIRE  
STAY  
M STAY  
armed.  
FIRE CHECK INSTANT  
NO AC Appears when AC power has been cut off.  
STYLE B  
System is operating on backup battery power.  
AC Appears when AC power is present.  
FIXED-WORD KEYPAD DISPLAYS  
CHIME Appears when the CHIME feature is ON.  
BAT Low system battery (if no zone number is shown),  
or Low battery condition in a wireless sensor  
(if zone number is also shown).  
ALARM Appears when an intrusion has been detected and the system is armed (also appears during  
a Fire alarm). Accompanied by the ID # of the zone in alarm.  
CHECK Appears when a malfunction is discovered in the system at any time or if a fault is detected  
in a FIRE zone at any time or in a DAY(Trouble)/NIGHT(Alarm) burglary zone during a  
disarmed period. Accompanied by a display of zone number in trouble.  
FIRE Appears when a fire alarm is present. Accompanied by a display of the zone # in alarm.  
– 11 –  
 
FUNCTIONS OF THE KEYPADS  
1. ALPHA DISPLAY WINDOW: A 1-line or 2-line, Liquid  
Crystal Display (LCD). Displays protection point  
6.  
TEST KEY: Tests the system and alarm sounder.  
identification and system status, messages, and user  
instructions.  
7.  
BYPASS KEY: Removes individual protection zones  
from being monitored by the system. Displays currently  
bypassed protection zones.  
2.  
3.  
OFF KEY: Disarms the burglary portion of the system,  
silences alarms and audible trouble indicators, and clears  
visual alarm trouble after the problem has been corrected.  
8.  
INSTANT KEY: Arms in manner similar to STAY mode,  
but turns off the entry delay period, offering greater security  
while inside and not expecting any late arrivals. An alarm  
will occur immediately upon opening any perimeter  
protection point, including entry delay zones  
AWAY KEY: Completely arms both perimeter and interior  
burglary protection for backup protection by sensing an  
intruder's movements through protected interior areas as  
well as guarding protected doors, windows, etc. Entrance  
can be made through an entry delay zone without causing  
an alarm if the system is disarmed before the entry delay  
time expires.  
9.  
CODE KEY: Allows the entry of additional user codes  
that can be given to other users of the system.  
10.  
CHIME KEY: Turns the CHIME mode on and off. When  
on, any entry through a protected delay or perimeter zone  
while the system is disarmed will cause a tone to sound at  
the Keypad(s).  
4.  
5.  
STAY KEY: Arms the perimeter burglary protection,  
guarding protected doors, windows and other perimeter  
protection points, and sounds an alarm if one is opened.  
Interior protection is not armed, which allows movement  
within your house without causing an alarm. Entrance can  
be made through an entry delay zone without causing an  
alarm if the system is disarmed before the entry delay time  
expires.  
11.  
12.  
READY KEY: When depressed prior to arming the  
system, the keypad will display all open protection zones  
within the keypad's home partition.  
use of  
KEY: Permits ARMING of the system without  
#
a security code ("Quick Arm", if programmed). Also used to  
view the second line of single-line Alpha keypads.  
MAXIMUM KEY: Arms in manner similar to AWAY mode,  
but eliminates the entry delay period, thus providing  
maximum protection. An alarm will occur immediately upon  
opening any protection point, including entry delay zones.  
13. KEYS 0-9: Used to enter your individual security access  
code(s).  
– 12 –  
 
14. POWER/READY INDICATOR: On  
keypads with a “POWER” LED, primary  
power is on when lit. If off, system is  
operating on backup battery power. On  
keypads with a “READY” LED, system is  
ready to be armed if lit, while unlit  
indicates system is not ready (a zone is  
open).  
1
2
3
5
4
6
7
15. ARMED INDICATOR: (RED) Lit when  
the system has been armed (STAY,  
AWAY, INSTANT or MAXIMUM).  
ARMED  
READY  
AWAY  
OFF  
STAY  
3
A
B
C
2
1
3
15  
14  
9
MAX  
TEST  
TEST  
BYPASS  
MAX  
BYPASS  
4
5
6
4
5
6
16. INTERNAL SOUNDER: Source of  
audible internal warning and confirmation  
sounds, as well as alarms (see  
"Summary of Audible Notifications").  
I
N
S
T
A
N
T
C
O
D
E
C
H
I
M
E
10  
7
7
8
9
9
16  
READY  
READY  
0
#
*
*
12  
PANIC  
17. A-B-C PANIC KEYS: Some keypads  
use key pairs to activate panic alarms,  
rather than individual keys. Refer to the  
PANIC KEYS section for descriptions of  
these keys.  
17  
8
11  
13  
SHOWN WITH  
KEYPAD COVER  
REMOVED  
IMPORTANT!: When you use the keypad  
to enter codes and commands, press the  
keys within 2 seconds of one another. If 2  
seconds elapse without a key depression,  
the entry is aborted and must be repeated  
from its beginning.  
TYPICAL ALPHA KEYPAD  
Fixed-Word Keypads are functionally similar, except for  
screen displays.  
– 13 –  
 
CHECKING FOR OPEN ZONES  
Using the *  
Before arming your system, all protected doors, windows and other protection zones  
must be closed or bypassed (see BYPASSING section). Otherwise the keypad will  
display a "Not Ready" message. Using the READY key will display all zones that are  
faulted, making it easier for you to secure any open zones.  
READY Key  
To show faulted zones:  
DIS ARMED- PRESS  
T O SH OW F AUL TS  
Note: A green READY indicator (if present) on the keypad will be lit  
if the system is ready to be armed. If not lit, the system is not ready.  
READY  
1.  
2.  
PRESS THE READY KEY  
Do not enter security code, but simply press the  
READY key.  
SECURE FAULTED ZONES  
Typical fault display shows open zones. Secure or  
bypass the zones displayed before arming the system.  
F AULT 05 F RONT  
UPS T AI RS BE DROOM  
3.  
SYSTEM CAN BE ARMED  
The "Ready" message will be displayed when all pro-  
tection zones have been either closed or bypassed.  
DI S ARME D  
RE ADY T O ARM  
* * *  
* * *  
You may now arm the system as usual.  
– 14 –  
 
ARMING PERIMETER ONLY  
(With Entry Delay ON)  
Using the  
3
Use this key when you are staying home, but might expect someone to use the  
entrance door later.  
STAY key  
When armed in STAY mode, the system will sound an alarm if a protected door or  
window is opened, but you may otherwise move freely throughout the premises. Late  
arrivals can enter through the entrance door without causing an alarm, but they must  
disarm the system within the entry delay period or an alarm will occur.  
Close all protected perimeter windows and doors before arming (see CHECKING  
FOR OPEN ZONES section). The green READY indicator (if present) on the keypad  
should be lit if the system is ready to be armed.  
STAY  
1.  
+
3
ENTER SECURITY CODE THEN PRESS STAY  
(Security Code)  
Example: 7 2 9 6 then press the STAY key.  
2.  
LISTEN FOR 3 BEEPS  
ARME D  
S T AY  
* * *  
* * *  
The keypad will beep three times and will display the  
armed STAY message. The red ARMED indicator also  
lights.  
You can restart the exit delay at any time after arming in STAY mode by pressing the  
key. This is useful if you wish to open the entry/exit door to let someone in after  
arming the system and avoids having to disarm the system and then re-arm it again.  
– 15 –  
 
ARMING PERIMETER ONLY  
(With Entry Delay OFF)  
Using the  
INSTANT  
Key  
Use this key when you are staying home and do not expect anyone to use the  
entrance door.  
7
When armed in INSTANT mode, the system will sound an alarm if a protected door or  
window is opened, but you may otherwise move freely throughout the premises. The  
alarm will also sound immediately if anyone opens the entrance door.  
Close all protected perimeter windows and doors before arming (see CHECKING  
FOR OPEN ZONES section). The green READY indicator (if present) on the keypad  
should be lit if the system is ready to be armed.  
INSTANT  
1.  
2.  
+
7
ENTER SECURITY CODE THEN PRESS INSTANT  
(Security Code)  
Example: 7 2 9 6 then press the INSTANT key.  
LISTEN FOR 3 BEEPS  
ARME D I NS T ANT  
*
*
The keypad will beep three times and will display the  
armed INSTANT message. The red ARMED indicator  
also lights.  
You can restart the exit delay at any time after arming in INSTANT mode by pressing  
the key. This is useful if you wish to open the entry/exit door to let someone in after  
arming the system and avoids having to disarm the system and then re-arm it again.  
– 16 –  
 
ARMING ALL PROTECTION  
(With Entry Delay ON)  
Using the  
Use this key when no one will be staying on the premises.  
2
AWAY Key  
When armed in AWAY mode, the system will sound an alarm if a protected door or  
window is opened, or if any movement is detected inside the premises. You may leave  
through the entrance door during the exit delay period without causing an alarm. You  
may also re-enter through the entrance door, but must disarm the system within the  
entry delay period or an alarm will occur.  
Close all protected perimeter windows and doors before arming (see CHECKING  
FOR OPEN ZONES section). The green READY indicator (if present) on the keypad  
should be lit if the system is ready to be armed.  
AWAY  
1.  
2.  
+
2
ENTER SECURITY CODE THEN PRESS AWAY  
(Security Code)  
Example: 7 2 9 6 then press the AWAY key.  
LISTEN  
ARME D AWAY  
Y OU MAY E X I T NOW  
* *  
* *  
The keypad will beep twice, or beep continuously if exit  
warning has been programmed for your system, and  
displays the armed AWAY message. The red ARMED  
indicator also lights.  
The "You May Exit Now" portion of the message  
disappears when the exit delay expires.  
– 17 –  
 
ARMING ALL PROTECTION  
(With Entry Delay OFF)  
Using the  
MAXIMUM  
Key  
Use this key when the premises will be vacant for extended periods of time such as  
vacations, etc., or when no one will be moving through protected interior areas.  
4
When armed in MAXIMUM mode, the system will sound an alarm if a protected door or  
window is opened, or if any movement is detected inside the premises. You may leave  
through the entrance door during the exit delay period without causing an alarm, but an  
alarm will be sounded as soon as someone re-enters.  
Close all protected perimeter windows and doors before arming (see CHECKING  
FOR OPEN ZONES section). The green READY indicator (if present) on the keypad  
should be lit if the system is ready to be armed.  
MAXIMUM  
1.  
+
4
ENTER SECURITY CODE THEN PRESS MAXIMUM  
(Security Code)  
Example: 7 2 9 6 then press the MAXIMUM key.  
LISTEN  
2.  
ARME D MAX I MUM  
Y OU MAY E X I T NOW  
*
*
The keypad will beep twice, or beep continuously if exit  
warning has been programmed for your system, and  
will display the armed MAXIMUM message  
(AWAY/INSTANT on fixed-word keypads). The red  
ARMED indicator also lights.  
The "You May Exit Now" portion of the message  
disappears when the exit delay expires.  
– 18 –  
 
DISARMING AND SILENCING ALARMS  
Using the  
OFF Key  
Use the OFF key to disarm the system and to silence alarm and trouble sounds. See  
"SUMMARY OF AUDIBLE NOTIFICATION" section for information which will help you  
to distinguish between FIRE and BURGLARY alarm sounds.  
1
IMPORTANT: If you return and the main burglary sounder is on, DO NOT enter the  
premises, but call the police from a nearby safe location. If you return after an alarm  
has occurred and the main sounder has shut itself off, the keypad will beep rapidly  
upon entering, indicating that an alarm has occurred during your absence and an  
intruder may still be on the premises. LEAVE IMMEDIATELY and CONTACT THE  
POLICE from a nearby safe location.  
To disarm the system and silence burglary alarms:  
OFF  
1.  
2.  
+
1
ENTER SECURITY CODE, THEN PRESS OFF  
(Security Code)  
Example: 7 2 9 6 then press the OFF key.  
LISTEN FOR 1 BEEP  
DI S ARME D  
* * *  
* * *  
The “Ready” message will be displayed (if no alarms  
have occurred while armed) and the keypad will beep  
once to confirm that the system is disarmed.  
RE ADY T O ARM  
– 19 –  
 
DISARMING AND SILENCING ALARMS  
(Continued)  
Memory of Alarm  
If an alarm occurs, the keypad displays the zone number (s) that caused the alarm and  
the type of alarm. These messages remain displayed until cleared by a user.  
To clear the display, note the zone number displayed and enter an OFF sequence  
(enter your security code and press the OFF key).  
If the “Ready“ message will not display, go to the displayed zone and correct the fault  
(close windows, etc.). If the fault cannot be corrected, notify your alarm company.  
– 20 –  
 
BYPASSING PROTECTION ZONES  
Using the  
6
This key is used when you want to arm your system with one or more zones  
intentionally unprotected. Bypassed zones are unprotected and will not cause an alarm  
when violated while your system is armed. All bypasses are removed when an OFF  
sequence (security code plus OFF) is performed. Bypasses are also removed if the  
arming procedure that follows the bypass command is not successful.  
BYPASS Key  
The system will not allow fire zones to be bypassed.  
To bypass zones, the system must be disarmed first.  
BYPASS  
1.  
+
6
ENTER SECURITY CODE THEN PRESS BYPASS  
(Security Code)  
(Zone Numbers)  
Example: 7 2 9 6 then press the BYPASS key.  
2.  
ENTER ZONE NUMBERS  
Enter the zone number(s) for the zones to be bypassed  
(e.g., 01, 02, 03, etc.).  
Important! All single-digit numbers must be preceded  
by a zero (for example, enter 01 for zone 1).  
3.  
4.  
WAIT  
BY PAS S 07 F RONT  
UPS T AI RS BE DROOM  
Typical bypass message  
The keypad will display the word BYPASS along with  
each bypassed zone number. Wait for these zones to  
be displayed, to be sure that intended zones are  
bypassed.  
ARM AS USUAL  
Arm the system as usual when the keypad displays the  
"Ready ” message.  
DI S ARME D BY PAS S  
RE ADY T O ARM  
– 21 –  
 
BYPASSING PROTECTION ZONES (Continued)  
Your system may allow you to easily bypass all open (faulted) zones without having to  
enter zone numbers individually. Ask your installer if this feature is active.  
Quick Bypass  
BYPASS  
1.  
2.  
+
6
ENTER SECURITY CODE THEN PRESS BYPASS  
(Security Code)  
Example: 7 2 9 6 then press the BYPASS key.  
WAIT  
BY PAS S 07 F RONT  
UPS T AI RS BE DROOM  
Typical bypass message  
In a few moments, all open zones will be displayed  
along with the word BYPASS. Wait for these zones to  
be displayed before arming. Arming the system before  
zones are displayed eliminates all bypasses.  
3.  
ARM AS USUAL  
Arm the system as usual when the keypad displays the  
"Ready" message.  
DI S ARME D BY PAS S  
RE ADY T O ARM  
Displaying  
Bypassed Zones  
For determining what zones have been previously bypassed. Bypassed zones can be  
displayed only when the system is disarmed, and when the “Bypass” message shown  
in step 3 above is displayed.  
BYPASS  
1.  
2.  
+
6
ENTER SECURITY CODE THEN PRESS BYPASS  
(Security Code)  
Example: 7 2 9 6 then press the BYPASS key.  
WAIT  
BY PAS S 07 F RONT  
UPS T AI RS BE DROOM  
Typical bypass message  
In a few moments, all open zones will be sequentially  
displayed along with the word BYPASS.  
– 22 –  
 
CHIME MODE  
Using the  
9
Key  
Your system can be set to alert you to the opening of a door or window† while it is  
disarmed by using CHIME mode. When activated, three beeps will sound at the  
keypad whenever a protected perimeter door or window is opened. Pressing the  
READY key will display the open protection points.  
Î or selected doors or  
windows if chime-by-zone  
feature is active. Ask  
installer if this feature  
applies to your system.  
Note that the Chime mode can be activated only when the system is disarmed.  
To turn Chime Mode on:  
CHIME  
1.  
2.  
+
9
ENTER SECURITY CODE THEN PRESS CHIME  
(Security Code)  
Example: 7 2 9 6 then press the CHIME key.  
VIEW  
DI S ARME D C HI ME  
RE ADY T O ARM  
The “Chime” message displays while chime mode is  
on.  
To turn Chime Mode off:  
CHIME  
1.  
+
9
ENTER SECURITY CODE THEN PRESS CHIME  
(Security Code)  
Example: 7 2 9 6 then press the CHIME key.  
2.  
VIEW  
DI S ARME D  
RE ADY T O ARM  
* * *  
* * *  
The “Chime” message disappears from the display.  
– 23 –  
 
PANIC KEYS  
(FOR MANUALLY ACTIVATING SILENT AND/OR AUDIBLE ALARMS)  
Using  
Panic Keys  
Your system may have been programmed to use special keys to manually activate  
panic functions. The functions that might be programmed are listed below. See your  
installer for the function(s) that may have been programmed for your system.  
Active Panic Functions  
Keys  
1 and Q  
3 and #  
Q and #  
A*  
Zone  
95  
96  
99  
95  
Function  
Your installer  
should note the  
functions that are  
are active in your  
system.  
B*  
99  
C*  
96  
* May not be present on your keypad(s).  
To use a paired key panic function, simply press both keys of the assigned pair at the  
same time. If your keypad has lettered keys for panic functions, press the designated  
key and hold down for at least 2 seconds to activate the panic function.  
Types of Panic  
Alarms  
A silent emergency sends an alarm signal  
to the alarm monitoring company,* but there  
will be no audible alarms or visual displays.  
An audible emergency sends an  
emergency message to the alarm monitoring  
company* and sounds a loud, steady alarm  
at your keypad and at any external sounders  
that may be connected (ALARM plus a zone  
number is also displayed).  
A personal emergency alarm sends an  
emergency message to the alarm monitoring  
company* and sounds at keypads, but not at  
external sounders. (ALARM plus a zone  
number is also displayed)  
* If your system is  
connected to an  
alarm monitoring  
company.  
A fire alarm sends a fire alarm message to  
the alarm monitoring company* and uniquely  
activates keypad and any external sounders  
(FIRE plus a zone number is also displayed).  
– 24 –  
 
USING DEVICE COMMANDS  
General  
Information  
Your system may be set up so that certain lights or other devices can be turned on or  
off by using the device command from the keypad. Ask your installer if this has been  
done in your system. If programmed for your system, some devices may activate  
automatically upon certain system conditions. In this case, the following commands  
can be used to override the device activation. See your installer for a full explanation of  
this feature.  
To activate devices  
ENTER SECURITY CODE THEN PRESS # + 7 + DEVICE NUMBER  
+
#
+ 7 +  
(Security Code)  
(Device Number)  
Example: 7 2 9 6 then press #, then press 7, then enter the number representing the  
device you wish to activate. See your installer for device numbers assigned for your system.  
To deactivate  
devices  
ENTER SECURITY CODE THEN PRESS # + 8 + DEVICE NUMBER  
+
#
+ 8 +  
(Security Code)  
(Device Number)  
Example: 7 2 9 6 then press #, then press 8, then enter the number representing the  
device you wish to deactivate. See your installer for device numbers assigned for your system.  
Device  
Description  
Device  
Description  
1
2
3
4
5
6
7
8
– 25 –  
 
PAGING FEATURE  
If the paging feature has been programmed for your system, your pager will respond to  
certain conditions as they occur in your system by displaying a 10-digit code. This  
code indicates the type of condition that has occurred.  
General  
Code Format  
The 10-digit pager code takes the following form:  
SSSS-EEE-NNN  
SSSS = 4-digit subscriber number (this number will always appear at the beginning of  
the pager display)  
EEE = 3-digit number describing the event that has occurred as follows:  
911 = Alarm (NNN following indicates the zone that caused the alarm)  
001 = Open, system disarmed (NNN following indicates user number)  
002 = Close, system armed (NNN following indicates user number)  
811 = Trouble (NNN following indicates the zone that caused the trouble)  
NNN = 3-digit user or zone number, depending on the type of event that occurred  
Examples:  
Pager displays: 1234–911–004  
This indicates that your system (subscriber 1234) is reporting an alarm (911) due to a  
fault on zone 4 (004).  
Pager displays: 1234–001–005  
This indicates that your system is reporting an open/disarm (001) by user 5 (005).  
– 26 –  
 
SECURITY CODES  
General Information  
As an additional safety feature, other users who do not have a need to know your code  
can be assigned different security codes. These secondary users are identified by  
"user numbers," which are selected when assigning a user's security code. You can  
assign up 14 additional user codes (user numbers 03-16), including the babysitter and  
duress codes. Note that the master (primary) user of the system is the only one who  
can assign codes to secondary (or temporary) users, and is user number 02; user  
number 01 is reserved for the installer of the system.  
All codes can be used interchangeably when performing system functions (a system  
armed with one user's code can be disarmed by another user's code), with the  
exception of the babysitter code described below.  
Babysitter Code This code can be used to arm the system in assigned partitions, but cannot disarm the  
system unless the system was armed with this code. This code is typically assigned to  
someone (such as a babysitter) who has a need to arm/disarm the system only at  
certain times. The babysitter code is assigned to user 15. The user of this code should  
not use the “Quick Arming” feature described below.  
Duress Code  
This feature is intended for use when you are forced to disarm or arm the system  
under threat. When used, the system will act normally, but can silently notify the alarm  
monitoring company of your situation, if that service has been provided. Duress code is  
assigned to user 16.  
Important: This code is useful only when the system is connected to a alarm  
monitoring company.  
Quick Arming  
Note that if "Quick Arming" was programmed by the installer, the  
#
key can be  
pressed in place of the security code when arming the system. The security code must  
always be used to disarm the system, however.  
– 27 –  
 
SECURITY CODES  
To Add a User or  
Change a User's  
Code  
Important: Temporary users of the system (e.g., babysitters, cleaning staff) should not be shown how to  
use any system function they do not need to know, such as bypassing protection zones for example.  
Sequential key depressions for all steps in a procedure must be made within 2  
seconds of one another, or else the entire entry is aborted and must be repeated from  
its beginning (e.g., perform steps 1, 2, and 3 below with no delay between steps).  
Changing the Master  
Code  
CODE  
1.  
2.  
+
8
ENTER MASTER CODE THEN PRESS CODE KEY  
Example: 7 2 9 6 then press the CODE key.  
ENTER USER NUMBER  
Follow the procedure  
for changing a user's  
code, but enter user  
#02. You will be  
prompted to enter the  
new code a second  
time to confirm  
(Master Code)  
(User Number)  
Enter the 2-digit User Number (03-16) for the user you  
are adding or changing.  
3.  
ENTER USER'S CODE  
accuracy.  
(User's Code)  
Enter the new 4-digit security code for that user.  
CODE  
To Delete a User  
1.  
2.  
+
8
ENTER MASTER CODE THEN PRESS CODE KEY  
Example: 7 2 9 6 then press the CODE key.  
ENTER USER NUMBER  
Enter the 2-digit User Number (03-16) for the user  
whose code you are deleting.  
(Master Code)  
(User Number)  
3. -----------  
STOP  
Wait (about 3 seconds) until the keypad beeps once  
before pressing any other key. The code is  
automatically deleted.  
– 28 –  
 
TESTING THE SYSTEM  
(TO BE CONDUCTED WEEKLY)  
Using the  
TEST Key  
The TEST key puts your system into the Test mode, which allows each protection  
point to be checked for proper operation. The keypad sounds a single beep every 40  
seconds as a reminder that the system is in the Test mode.  
5
Note: An alarm message will not be sent to be sent to your alarm monitoring  
company during the following tests.  
1.  
DISARM THE SYSTEM  
DI S ARME D  
RE ADY T O ARM  
* * *  
* * *  
Disarm the system and close all protected windows,  
doors, etc. The “Ready” message should be displayed  
and the green READY indicator (if present on the  
keypad) should also be lit .  
TEST  
2.  
3.  
+
5
ENTER THE SECURITY CODE THEN PRESS TEST  
(Security Code)  
Example: 7 2 9 6 then press the TEST key.  
LISTEN. The external sounder should sound for 2  
seconds and then turn off.  
If the sounder does not sound, CALL FOR SERVICE  
IMMEDIATELY.  
4.  
FAULT ZONES. Open each protected door and window  
in turn and listen for three beeps from the keypad.  
Identification of each faulted protection point should  
appear on the display. The display will clear when the  
door or window is closed.  
(Continued)  
– 29 –  
 
TESTING THE SYSTEM  
Walk in front of any interior motion detectors (if used) and  
listen for three beeps. The identification of the detector  
should appear on the display when it is activated. The  
display will clear when no motion is detected. Note that if  
wireless motion detectors are used, there is a 3-minute  
delay between activations. This is to conserve battery  
life.  
To test all smoke detectors, follow the manufacturer's  
instructions. The identification of each detector should  
appear on the display when each is activated.  
If a problem is experienced with any protection point (no  
confirming sounds, no display), CALL FOR SERVICE  
IMMEDIATELY.  
When all protection points have been checked and are  
intact (closed), there should be no zone identification  
numbers displayed on the keypad.  
When testing is completed, exit the TEST mode by  
continuing with step 5.  
OFF  
5.  
+
1
EXIT TEST MODE  
(Security Code)  
Enter your security code and press the OFF key.  
If the test mode is inadvertently left active, it  
automatically turns off after 4 hours.  
– 30 –  
 
TROUBLE CONDITIONS  
The word CHECK on the Keypad's display, accompanied by a rapid "beeping" at the  
Keypad, indicates that there is a trouble condition in the system. The displays in  
parenthesis may appear on non-alpha keypads when the associated trouble condition  
is present.  
Typical "Check"  
Displays  
To silence the beeping sound for "check" conditions, press any key.  
1. CHECK +  
Zone  
Indicates that a problem exists with those zone(s)*. First, deter-  
mine if the zone(s) displayed are intact and make them so if they  
are not. If the zone uses a wireless detector, check that changes  
in the room (moving furniture, televisions, etc.) are not blocking  
wireless signals from the detector. If the problem has been cor-  
rected, the zone descriptor(s) and CHECK should disappear. If not,  
key an OFF sequence (security code plus OFF) to clear the dis-  
play. A CHECK condition can also indicate a wiring problem. If the  
“check” display persists, CALL FOR SERVICE IMMEDIATELY.  
* Note that zone  
number 9 repre-  
sents a problem  
with wireless re-  
ceivers or other  
system devices,  
which are not user  
serviceable. CALL  
FOR SERVICE  
IMMEDIATELY.  
Descriptors  
Note that the system will not allow arming if a CHECK condition  
exists. To arm the system with a CHECK condition present, you  
must first bypass the zone(s) having the CHECK condition.  
2. Telco Fault  
(or CHECK  
If the telephone line monitor feature has been programmed for your  
system, this display indicates that the telephone line has been  
disconnected or cut. In some systems, this display will be  
accompanied by a trouble sound from the keypad and the external  
sounder may be activated. CONTACT YOUR SERVICE  
COMPANY IMMEDIATELY.  
and zone 94)  
To silence the trouble sound, enter your security code plus OFF.  
– 31 –  
 
TROUBLE CONDITIONS (Continued)  
3. COMM. FAILURE (or F C) Indicates that a failure has occurred in the  
* The beeping that  
accompanies a low  
battery display (items  
4 and 5) can be  
stopped by entering  
an OFF sequence  
(code + OFF)  
telephone communication portion of your system.  
CALL FOR SERVICE IMMEDIATELY.  
4. SYSTEM LO BAT  
Indicates that a low system battery condition exists,  
(or BAT with no zone No.) accompanied by a once-per-minute "beeping"* at  
the Keypad. CALL FOR SERVICE IMMEDIATELY.  
5. LO BAT + zone descriptor  
Indicates that a low battery condition exists in the  
wireless transmitter** displayed, and accompanied  
by a once-per-minute "beeping"* at the Keypad.  
CALL FOR SERVICE IMMEDIATELY.  
** Not all systems use  
wireless transmitters.  
(or BAT with zone No.)  
6. MODEM COMM  
Indicates that the control is on-line with the central  
station's remote computer. The control will not  
operate while on-line. Wait a few minutes. The  
display should disappear.  
(or CC)  
7. POWER indicator (if present) The system is operating on battery power only.  
is off. AC LOSS is displayed If only some lights are out on the premises, check  
(or NO AC)  
circuit breakers and fuses and reset or replace as  
necessary. CALL FOR SERVICE IMMEDIATELY if  
AC power cannot be restored to the system.  
8. Busy-Standby (or dI)  
If this remains displayed for more than 1 minute,  
system is disabled. CALL FOR SERVICE AT ONCE.  
9. OPEN CIRCUIT (or OC)  
The keypad is not receiving signals from the control.  
10. Long Rng Trbl (or bF) If programmed, back-up Long Range Radio  
communication has failed. CALL FOR SERVICE AT  
ONCE.  
– 32 –  
 
FIRE ALARM SYSTEM (IF INSTALLED)  
General  
Your fire alarm system (if installed) is active 24 hours a day, providing continuous  
protection. In the event of an emergency, the installed smoke and heat detectors will  
automatically activate you security system, triggering a loud, interrupted sound from  
the Keypad. An interrupted sound will also be produced by optional exterior sounders.  
A FIRE message will appear at your Keypad and remain on until you silence and clear  
the alarm display.  
1. Should you become aware of a fire emergency before your detectors sense the  
problem, go to your nearest Keypad and press the single panic key (or panic key  
pair) assigned as FIRE emergency (if programmed by the installer) and hold down  
for at least 2 seconds. The alarm will sound.  
In Case Of Fire  
2. Evacuate all occupants from the premises.  
3. If flames and/or smoke are present, leave the premises and notify your local Fire  
Department immediately.  
4. If no flames or smoke are apparent, investigate the cause of the alarm. The zone  
descriptor of the zone(s) in an alarm condition will appear at the Keypad.  
Silencing A Fire  
Alarm  
1. Silence the alarm by pressing the OFF key. To clear the alarm display, enter your  
code and press the OFF key again.  
2. If the Keypad indicates a trouble condition after the second OFF sequence, check  
that smoke detectors are not responding to smoke or heat producing objects in  
their vicinity. Should this be the case, eliminate the source of heat or smoke.  
3. If this does not remedy the problem, there may still be smoke in the detector. Clear  
it by fanning the detector for about 30 seconds.  
4. When the problem has been corrected, clear the display by entering your code and  
pressing the OFF key.  
– 33 –  
 
NATIONAL FIRE PROTECTION ASSN.  
RECOMMENDATIONS ON SMOKE DETECTORS  
With regard to the number and placement of smoke/heat detectors, we subscribe to the  
recommendations contained in the National Fire Protection Association's (NFPA) Standard #74  
noted below.  
Early warning fire detection is best achieved by the installation of fire detection equipment in all  
rooms and areas of the household as follows: A smoke detector installed outside of each  
separate sleeping area, in the immediate vicinity of the bedrooms and on each additional story  
of the family living unit, including basements and excluding crawl spaces and unfinished attics.  
In addition, the NFPA recommends that you install heat or smoke detectors in the living room,  
dining room, bedroom(s), kitchen, hallway(s), attic, furnace room, utility and storage rooms,  
basements and attached garages.  
KITCHEN  
KITCHEN  
BDRM  
DINING  
BEDROOM  
BEDROOM  
TV ROOM  
DINING  
BDRM  
LIVING ROOM  
BEDROOM  
BEDROOM  
BEDROOM  
BEDROOM  
BEDROOM  
LIVING ROOM  
TO  
BR  
KTCHN  
GARAGE  
CLOSED  
DOOR  
LVNG RM  
.
Smoke Detectors for Minimum Protection  
Smoke Detectors for Additional Protection  
Heat-Activated Detectors  
BASEMENT  
– 34 –  
 
EMERGENCY EVACUATION  
Establish and regularly practice a plan of escape in the event of fire. The  
following steps are recommended by the National Fire Protection Association:  
1. Position your detector or your interior and/or exterior sounders so that they  
can be heard by all occupants.  
2. Determine two means of escape from each room. One path of escape  
should lead to the door that permits normal exit from the building. The other  
may be a window, should your path be unpassable. Station an escape  
ladder at such windows if there is a long drop to the ground.  
2ND FLOOR  
3. Sketch a floor plan of the building. Show windows, doors, stairs and  
rooftops that can be used to escape. Indicate escape routes for each room.  
Keep these routes free from obstruction and post copies of the escape  
routes in every room.  
BACK DOOR  
1ST FLOOR  
4. Assure that all bedroom doors are shut while you are asleep. This will  
prevent deadly smoke from entering while you escape.  
5. Try the door. If the door is hot, check your alternate escape route. If the  
door is cool, open it cautiously. Be prepared to slam the door if smoke or  
heat rushes in.  
6. When smoke is present, crawl on the ground. Do not walk upright, since  
smoke rises and may overcome you. Clearer air is near the floor.  
BACK  
7. Escape quickly; don't panic.  
8. Establish a common meeting place outdoors, away from your house, where  
everyone can meet and then take steps to contact the authorities and ac-  
count for those missing. Choose someone to assure that nobody returns to  
the house — many die going back.  
FRONT  
– 35 –  
 
MAINTAINING YOUR SYSTEM  
Taking Care of  
Your System  
The components of your security system are designed to be as maintenance-free as  
possible. However, to make sure that your system is in reliable working condition.  
1. Test your system weekly.  
2. Test your system after any alarm occurs (see TESTING THE SYSTEM).  
Replacing  
Batteries in  
Wireless  
Each wireless sensor in your system has a 9-volt or 3-volt battery. The system detects  
a low battery in any wireless sensor, including smoke detectors, the optional personal  
emergency transmitter, and the optional portable wireless keypad. (A low battery in a  
portable wireless keypad is detected as soon as one of its keys is pressed, and the  
wired keypad will display “00”.)  
Alkaline batteries provide a minimum of 1 year of operation, and in most units and  
applications, provide 2–4 years of service. 3-volt lithium batteries provide up to 4 or  
more years of operation. Actual battery life will depend on the environment in which the  
sensor is used, the number of signals that the transmitter in the sensor has had to  
send, and the specific type of sensor. Factors such as humidity, high or low  
temperatures or large swings in temperature, may all lead to the reduction of actual  
battery life in an installation.  
Sensors  
Wireless sensors  
may not have been  
used in your  
security system  
If you have a low battery in a wireless sensor, a low battery message i s  
displayed on the keypad.  
In addition, a battery-operated smoke detector with a low battery also emits a single  
"chirp" sound approximately once every 20–30 seconds, identifying itself as the smoke  
detector with the weak battery.  
Note: The low battery message comes on as a warning that battery replacement in  
indicated sensor(s) is due within 30 days. In the meantime, a sensor causing a low  
battery indication is still fully operational.  
Important: Use only batteries recommended by your installer as replacement.  
– 36 –  
 
MAINTAINING YOUR SYSTEM  
Silencing Low  
Battery Warning  
Tones at the  
Keypad  
You can silence the keypad’s warning tones by pressing the OFF key, but the  
keypad's low battery message display will remain on as a reminder that you have a  
low battery condition in one or more of your sensors. When you replace the weak  
battery with a fresh one, the sensor will send a "good battery" signal to the control as  
soon as the sensor is activated (opening/closing of door, window, etc.), causing the  
low battery display to turn off. If the sensor is not activated, the display will  
automatically clear within approximately 1 hour.  
Routine Care  
Treat the components of your security system as you would any other electrical  
equipment. Do not slam sensor-protected doors or windows.  
Keep dust from accumulating on the keypad and all protective sensors, particularly on  
motion sensors and smoke detectors.  
The keypad and sensors should be cleaned carefully with a dry soft cloth. Do not  
spray water or any other fluid on the units.  
– 37 –  
 
QUICK GUIDE TO  
SYSTEM FUNCTIONS  
FUNCTION  
Check Zones  
Arm System  
PROCEDURE  
Press [Q]  
Enter code  
Press arming key desired  
(AWAY, STAY, INSTANT,  
MAXIMUM)  
COMMENTS  
Do this to view faulted zones when system not ready.  
Do this to arm the system in the mode selected.  
Disarm System  
Bypass zones  
Enter code  
Press OFF [1]  
Do this to disarm the system and silences alarms.  
Enter code  
Press BYPASS [6]  
Do this to bypass protection zones. Bypassed zones are un-  
protected and will not cause an alarm if violated.  
Enter zone numbers to be  
bypassed (use 2-digit entries)  
Enter code  
Quick Bypass  
Do this to bypass all faulted zones automatically, if programmed.  
Press BYPASS [6] and stop  
Chime Mode ON Enter code  
Press CHIME [9]  
Chime Mode OFF Enter code  
Press CHIME [9]  
Enter code  
Press TEST [5]  
Do this to turn on chime mode. Keypad will sound if doors or  
windows are violated while system disarmed.  
Do this to turn chime mode off.  
Test Mode ON  
Do this to enter test mode. Sounds alarm sounder and allows  
sensors to be tested.  
Do this to turn test mode off. System returns to normal mode.  
Test Mode OFF Enter code  
Press OFF [1]  
– 38 –  
 
QUICK GUIDE TO  
SYSTEM FUNCTIONS  
FUNCTION  
PROCEDURE  
COMMENTS  
Add or Change  
a User  
Enter master code  
Press CODE [8]  
Enter user's 2-digit user No.  
Enter code for that user  
Do this to add or change a user code.  
Delete a User  
Enter master code  
Press CODE [8]  
Enter user number to be  
deleted  
Do this to delete a user code from the system.  
Do this to change the existing master code.  
Change a Master Enter master code  
Code  
Press CODE [8]  
Press [0] + [2] (master user no.)  
Enter new 4-digit master code  
Enter new master code again  
– 39 –  
 
SUMMARY OF AUDIBLE NOTIFICATION  
(ALPHA DISPLAY KEYPADS)  
SOUND  
CAUSE  
FIRE ALARM  
DISPLAY  
LOUD, INTERRUPTED*  
Keypad & External  
LOUD, CONTINUOUS*  
Keypad & External  
ONE SHORT BEEP  
(not repeated)  
FIRE is displayed; descriptor of zone in alarm is displayed.  
BURGLARY/AUDIBLE  
EMERGENCY ALARM  
a. SYSTEM DISARM  
b. SYSTEM ARMING ATTEMPT  
WITH AN OPEN ZONE.  
ALARM is displayed; descriptor of zone in alarm is also displayed.  
a. DISARMED/READY TO ARM is displayed.  
b. The number and descriptor of the open protection zone is displayed.  
c. Numbers and descriptors of the bypassed protection zones are displayed  
(One beep is heard for each zone displayed). Subsequently, the following is  
displayed: DISARMED BYPASS Ready to Arm  
Keypad only  
c. BYPASS VERIFY  
ONE SHORT BEEP  
SYSTEM IS IN TEST MODE  
Opened Zone identifications will appear.  
(once every 40 seconds)  
Keypad only  
ONE BEEP every 40 sec.  
Keypad only  
LOW BATTERY AT A TRANSMITTER LO BAT displayed with description of transmitter.  
TWO SHORT BEEPS  
Keypad only  
ARM AWAY OR MAXIMUM  
a. ARM STAY OR INSTANT  
ARMED AWAY or ARMED MAXIMUM displayed. Red ARMED indicator lit.  
THREE SHORT BEEPS  
Keypad only  
a. ARMED STAY or ARMED INSTANT displayed. Red ARMED indicator lit.  
b. CHIME displayed, descriptor of open protection zone will be displayed if the  
[Q] key is pressed.  
b. ZONE OPENED WHILE SYSTEM  
IS IN CHIME MODE.  
RAPID BEEPING  
Keypad only  
a. TROUBLE  
a. CHECK displayed. Descriptor of troubled protection zone is displayed.  
b. FIRE or ALARM is displayed; descriptor of zone in alarm is displayed.  
b. MEMORY OF ALARM  
a. EXIT DELAY WARNING (if  
programmed)  
SLOW BEEPING  
Keypad only  
a. ARMED AWAY or ARMED MAXIMUM is displayed along with You May  
Exit Now  
b. DISARM SYSTEM OR ALARM WILL OCCUR is displayed. Exceeding the  
delay time without disarming causes alarm.  
b. ENTRY DELAY WARNING  
* If a bell is used as external sounder, fire alarm is pulsed ring; burglary/audible emergency is steady ring.  
– 40 –  
 
GLOSSARY  
The following terms are used throughout the manual.  
ARM/DISARM: "Armed" simply means that the burglary portion of your system is turned ON and is in a  
state of readiness. "Disarmed" means that the burglary system is turned OFF, and  
must be rearmed to become operational. However, even in a "disarmed" state,  
"emergency" and "fire" portions of your system are still operational.  
KEYPAD: This is the area on your Keypad containing numbered pushbuttons similar to those on  
telephones or calculators. These keys control the arming or disarming of the system,  
and perform other functions which were previously described in this manual.  
ZONE: A specific area of protection.  
PARTITION: An independent group of zones that can be armed and disarmed without affecting  
other zones or users.  
BYPASS: To disarm a specific area of burglary protection while leaving other areas operational.  
DELAY ZONE: An area of protection containing doors most frequently used to enter or exit (typically, a  
front door, back door, or door from the garage into the building). The delay zone allows  
sufficient time for authorized entry or exit without causing an alarm. Consult your  
installer for the entry and exit delay times that have been set for your system during  
installation and record them in the space provided in this manual on page 7.  
DAY/NIGHT ZONE: An area of protection whose violation causes a trouble indication during the disarmed  
(DAY) mode and an alarm during the armed (NIGHT) mode.  
– 41 –  
 
UL NOTICE: This is a "GRADE A" system.  
FEDERAL COMMUNICATIONS COMMISSION (FCC) Part 15 STATEMENT  
This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following  
statement for your information:  
This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with  
the manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to comply  
with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules, which are designed to  
provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference  
will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be  
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the  
following measures:  
If using an indoor antenna, have a quality outdoor antenna installed.  
Reorient the receiving antenna until interference is reduced or eliminated.  
Move the receiver away from the control/communicator.  
Move the antenna leads away from any wire runs to the control/communicator.  
Plug the control/communicator into a different outlet so that it and the receiver are on different branch circuits.  
If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions.  
The user or installer may find the following booklet prepared by the Federal Communications Commission helpful: "Interference  
Handbook". This booklet is available from the U.S. Government Printing Office, Washington, DC 20402.  
The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's  
Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment.  
IN THE EVENT OF TELEPHONE OPERATIONAL PROBLEMS  
In the event of telephone operational problems, disconnect the control by removing the plug from the RJ31X (CA38A in Canada)  
telephone wall jack. We recommend that your certified installer demonstrate disconnecting the phones on installation of the system. Do  
not disconnect the phone connection inside the control/communicator. Doing so will result in the loss of your phone lines. If the regular  
phone works correctly after the control/communicator has been disconnected from the phone lines, the control/communicator has a  
problem and should be returned for repair. If upon disconnection of the control/communicator, there is still a problem on the line, notify  
the telephone company that they have a problem and request prompt repair service. The user may not under any circumstances (in or  
out of warranty) attempt any service or repairs to the system. It must be returned to the factory or an authorized service agency for all  
repairs.  
– 42 –  
 
FEDERAL COMMUNICATIONS COMMISSION (FCC) Part 68 NOTICE  
This equipment complies with Part 68 of the FCC rules. On the front cover of this equipment is a label that contains,  
among other information, the FCC registration number and ringer equivalence number (REN) for this equipment. If  
requested, this information must be provided to the telephone company.  
This equipment uses the following jacks:  
An RJ31X is used to connect this equipment to the telephone network.  
The REN is used to determine the quantity of devices which may be connected to the telephone line. Excessive RENs  
on the telephone line may result in the devices not ringing in response to an incoming call. In most, but not all areas, the  
sum of the RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to the line,  
as determined by the total RENs, contact the telephone company to determine the maximum REN for the calling area.  
If this equipment causes harm to the telephone network, the telephone company will notify you in advance that  
temporary discontinuance of service may be required. If advance notice is not practical, the telephone company will  
notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you  
believe necessary.  
The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the  
operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make  
the necessary modifications in order to maintain uninterrupted service.  
If trouble is experienced with this equipment, please contact the manufacturer for repair and warranty information. If the  
trouble is causing harm to the telephone network, the telephone company may request you remove the equipment from  
the network until the problem is resolved.  
There are no user serviceable components in this product, and all necessary repairs must be made by the  
manufacturer. Other repair methods may invalidate the FCC registration on this product.  
This equipment cannot be used on telephone company-provided coin service. Connection to Party Line Service is  
subject to state tariffs.  
This equipment is hearing-aid compatible.  
When programming or making test calls to an emergency number, briefly explain to the dispatcher the reason for the  
call. Perform such activities in the off-peak hours; such as early morning or late evening.  
– 43 –  
 
WARNING!  
THE LIMITATIONS OF THIS ALARM SYSTEM  
While this system is an advanced design security system, it does not offer guaranteed protection against burglary or fire or other  
emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a variety of reasons.  
For example:  
• Intruders may gain access through unprotected openings or have the technical sophistication to bypass an alarm sensor or  
disconnect an alarm warning device.  
• Intrusion detectors (e.g. passive infrared detectors), smoke detectors, and many other sensing devices will not work without power.  
Battery operated devices will not work without batteries, with dead batteries, or if the batteries are not put in properly. Devices  
powered solely by AC will not work if their AC power supply is cut off for any reason, however briefly.  
• Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm receiver. Even if the signal  
path has been recently checked during a weekly test, blockage can occur if a metal object is moved into the path.  
• A user may not be able to reach a panic or emergency button quickly enough.  
• While smoke detectors have played a key role in reducing residential fire deaths in the United States, they may not activate or  
provide early warning for a variety of reasons in as many as 35% of all fires, according to data published by the Federal Emergency  
Management Agency. Some of the reasons smoke detectors used in conjunction with this System may not work are as follows.  
Smoke detectors may have been improperly installed and positioned. Smoke detectors may not sense fires that start where smoke  
cannot reach the detectors, such as in chimneys, in walls, or roofs, or on the other side of closed doors. Smoke detectors also may  
not sense a fire on another level of a residence or building. A second floor detector, for example, may not sense a first floor or  
basement fire. Moreover, smoke detectors have sensing limitations. No smoke detector can sense every kind of fire every time. In  
general, detectors may not always warn about fires caused by carelessness and safety hazards like smoking in bed, violent  
explosions, escaping gas, improper storage of flammable materials, overloaded electrical circuits, children playing with matches, or  
arson. Depending upon the nature of the fire and/or the locations of the smoke detectors, the detector, even if it operates as  
anticipated, may not provide sufficient warning to allow all occupants to escape in time to prevent injury or death.  
• Passive Infrared Motion Detectors can only detect intrusion within the designed ranges as diagrammed in their installation manual.  
Passive Infrared Detectors do not provide volumetric area protection. They do create multiple beams of protection, and intrusion  
can only be detected in unobstructed areas covered by those beams. They cannot detect motion or intrusion that takes place  
behind walls, ceilings, floors, closed doors, glass partitions, glass doors, or windows. Mechanical tampering, masking, painting or  
spraying of any material on the mirrors, windows or any part of the optical system can reduce their detection ability. Passive  
Infrared Detectors sense changes in temperature; however, as the ambient temperature of protected area approaches the  
temperature range of 90° to 105°F, the detection performance can decrease.  
– 44 –  
 
WARNING!  
THE LIMITATIONS OF THIS ALARM SYSTEM  
(continued)  
• Alarm warning devices such as sirens, bells or horns may not alert people or wake up sleepers if they are located on the other side  
of closed or partly open doors. If warning devices sound on a different level of the residence from the bedrooms, then they are less  
likely to waken or alert people inside the bedrooms. Even persons who are awake may not hear the warning if the alarm is muffled  
from a stereo, radio, air conditioner or other appliance, or by passing traffic. Finally, alarm warning devices, however loud, may not  
warn hearing-impaired people or waken deep sleepers.  
• Telephone lines needed to transmit alarm signals from a premises to a central monitoring station may be out of service or  
temporarily out of service. Telephone lines are also subject to compromise by sophisticated intruders.  
• Even if the system responds to the emergency as intended, however, occupants may have insufficient time to protect themselves  
from the emergency situation. In the case of a monitored alarm system, authorities may not respond appropriately.  
• This equipment, like other electrical devices, is subject to component failure. Even though this equipment is designed to last as  
long as 10 years, the electronic components could fail at any time.  
The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance. This alarm  
system should be tested weekly to make sure all sensors and transmitters are working properly.  
Installing an alarm system may make one eligible for lower insurance rates, but an alarm system is not a substitute for insurance.  
Homeowners, property owners and renters should continue to act prudently in protecting themselves and continue to insure their lives  
and property.  
We continue to develop new and improved protection devices. Users of alarm systems owe it to themselves and their loved ones to  
learn about these developments.  
– 45 –  
 
CANADIAN DEPARTMENT OF COMMUNICATIONS (DOC) STATEMENT  
NOTICE  
AVIS  
The Canadian Department of Communications label identifies certified  
equipment. This certification means that the equipment meets certain  
telecommunications network protective, operational and safety  
requirements. The Department does not guarantee the equipment will  
operate to the user's satisfaction.  
L'étiquette du ministère des Communications du Canada identifie le  
matériel homologué. Cette étiquette certifie que le matériel est conforme  
à certaines normes de protection, d'exploitation et de sécurité des  
réseaux de télécommunications. Le ministère n'assure toutefois pas que  
le matériel fonctionnera à la satisfaction de l'utilisateur.  
Avant d'installer ce matériel, l'utilisateur doit s'assurer qu'il est permis de  
le raccorder aux installations de l'entreprise locale de  
télécommunications. Le matériel doit également être installé en suivant  
une méthode acceptée de raccordement. Dans certains cas, les fils  
intérieurs de l'entreprise utilisés pour un service individuel à la ligne  
unique peuvent être prolongés au moyen d'un dispositif homologué de  
raccordement (cordon prolongateur téléphonique interne). L'abonné ne  
doit pas oublier qu'il est possible que la conformité aux conditions  
énoncées ci-dessus n'empèchet pas la dégradation du service dans  
certaines situations. Actuellement, les entreprises de télécommunications  
ne permettent pas que l'on raccorde leur matériel aux prises d'abonnés,  
sauf dans les cas precis prévus par les tarifs particuliers de ces  
entreprises.  
Before installing this equipment, users should ensure that it is permissible  
to be connected to the facilities of the local telecommunications company.  
The equipment must also be installed using an acceptable method of  
connection. In some cases, the company's inside wiring associated with a  
single line individual service may be extended by means of certified  
connector assembly (telephone extension cord). The customer should be  
aware that compliance with the above conditions may not prevent  
degradation of service in some situations.  
Repairs to certified equipment should be made by an authorized  
Canadian maintenance facility designated by the supplier. Any repairs or  
alterations made by the user to this equipment, or equipment  
malfunctions, may give the telecommunications company cause to  
request the user to disconnect the equipment.  
Les réparations du matériel homologué doivent être effectuées pas un  
centre d'entretien canadien autorisé désigné par le fournisseur. La  
compagnie de télécommunications peut demander à l'utilisateur de  
débrancher un appareil à la suite de réparations ou de modifications  
effectuées par l'utilisateur ou à cause de mauvais fonctionnement.  
Users should ensure for their own protection that the electrical ground  
connections of the power utility, telephone lines and internal metallic  
water pipe system, if present, are connected together. This precaution  
may be particularly important in rural areas.  
Caution: User should not attempt to make such connections themselves,  
but should contact the appropriate electric inspection authority, or  
electrician, as appropriate.  
Pour sa propre protection, l'utilisateur doit s'assurer que tous les fils de  
mise en terre de la source d'énergie électrique, des lignes téléphoniques  
de réseau de conduites d'eau s'il y en a, soient raccordés ensemble.  
Cette précaution est particulièrement importante dans les régions rurales.  
Avertissement: L'utilisateur ne doit pas tenter de faire ces  
raccordements lui-même; il doit avoir recours à un service d'inspection  
des installations électriques, ou à un électricien, selon le cas.  
L'indice de charge (IC) assigné à chaque dispositif terminal pour éviter  
toute surcharge indique le pourcentage de la charge totale qui peut être  
raccordé à un circuit téléphonique bouclé utilisé par ce dispositif. La  
terminaison du circuit bouclé peut être constituée de n'importe quelle  
combinaison de dispositifs, pourvu que la somme des indices de charge  
de l'ensemble des dispositifs ne dépasse pas 100.  
The Load Number (LN) assigned to each terminal device denotes the  
percentage of the total load to be connected to a telephone loop which is  
used by the device, to prevent overloading. The termination on a loop  
may consist of any combination of devices subject only to the requirement  
that the total of the Load Numbers of all the devices does not exceed 100.  
– 46 –  
 
OWNER'S INSURANCE PREMIUM CREDIT REQUEST  
This form should be completed and forwarded to your homeowner's insurance carrier for possible premium credit.  
A. GENERAL INFORMATION:  
Insured's Name and Address:  
Insurance Company:  
Policy No.:  
Other ___________________________  
ADEMCO's VISTA 20SE  
Type of Alarm:  
Burglary  
Fire  
Both  
Installed by:  
Serviced by:  
Name  
Name  
Address  
Address  
B. NOTIFIES (Insert B = Burglary, F = Fire)  
Local Sounding Device  
Police Dept.  
Fire Dept.  
Central Station  
Name: _______________________________________________________________________  
Address:  
Phone:  
C. POWERED BY: A.C. With Rechargeable Power Supply  
D. TESTING: Quarterly Monthly  
Weekly  
Other  
continued on other side  
– 47 –  
 
OWNER'S INSURANCE PREMIUM CREDIT REQUEST (cont.)  
E. SMOKE DETECTOR LOCATIONS  
Furnace Room  
Kitchen  
Bedrooms  
Attic  
Hall  
Basement  
Living Room  
Dining Room  
F. BURGLARY DETECTING DEVICE LOCATIONS:  
Front Door  
Basement Door  
Rear Door  
All Exterior Doors  
1st Floor Windows  
All windows  
I nterior locations  
All Accessible Openings, Including Skylights, Air Conditioners and Vents  
G. ADDITIONAL PERTINENT INFORMATION:  
Signature:  
Date:  
– 48 –  
 
SERVICING INFORMATION  
Your local Ademco dealer is the person best qualified to service your alarm system.  
Arranging some kind of regular service program with him is advisable.  
Your local Ademco dealer is:  
Name:  
Address:  
Phone:  
– 49 –  
 
– INDEX –  
1-Line Alpha Keypads ......................9  
2-Partition AWAY Arming................17  
AC Loss .........................................32  
Add A User .....................................28  
Alpha Keypad ...................................9  
Audible Emergency ............11, 24, 40  
Away ............5, 11, 12, 17, 26, 38, 40  
Away Mode ........................12, 17, 26  
Babysitter Code .............................27  
Burglary Protection .................4, 5, 41  
Bypass ...............................12, 14, 21  
Check .......................................11, 31  
Chime ...........................................5, 7  
Chime Mode ...............5, 9, 11, 38, 40  
Comm. Failure ................................32  
Common Zone ..................................8  
Delete A User ...........................28, 39  
Disarming .....................20, 26, 38, 41  
Displaying Bypassed Zones............22  
Duress Code ............................13, 27  
Emergency Evacuation ..................35  
Entry Delay .............................5, 7, 11  
Exit Delay .. 5, 7, 8, 17, 18, 19, 40, 41  
Exit Alarm ......................................... 8  
Fire .......... 4, 6, 11, 20, 21, 33, 35, 41  
Fire Alarm ................................ 33, 40  
Fire Protection ................................. 6  
Fire Escape .................................... 35  
Fixed-Word Keypads ................. 9, 11  
Instant ............... 5, 11, 12, 16, 38, 40  
Instant Mode ................................. 16  
Keypads .................. 9, 10, 11, 12, 13  
Lo Bat ...................................... 32, 40  
Low Battery ............ 11, 32,36, 37, 40  
Maximum ............. 5, 7, 12, 19, 38, 40  
Maximum Mode ............................. 19  
Memory Of Alarm .......... 6, 20, 26, 40  
Modem Comm ............................... 32  
National Fire Protect Assn. ..... 34, 35  
Not Ready ............. 11, 14, 18, 26, 38  
Off Key .......................................... 20  
Paging Feature ............................... 26  
Panic Functions ............................. 24  
Panic Keys ............................... 12, 33  
Partitioned System .......................... 4  
Personal Emergency ..................... 24  
Quick Arming ................................. 27  
Quick Bypass.................................. 22  
Ready Key ............................... 14, 33  
Security Codes .................... 5, 27, 28  
Silence Alarm ................................ 20  
Silent Emergency .......................... 24  
Sounder ....... 76, 9, 12, 20, 24, 29, 40  
Special AWAY Arming .................... 17  
Stay ............. 5, 11, 12, 15, 26, 38, 40  
Stay Mode ......................... 12, 15, 26  
System Lo Battery ......................... 32  
Temporary Users ........................... 28  
Test Key ........................................ 29  
Test Mode .................... 29, 30, 38, 40  
Trouble Conditions .................. 31, 32  
User Number ..................... 27, 38, 39  
Voice Module ................................... 6  
Wireless Sensor ...................... 11, 36  
Zones .............................................. 4  
– 50 –  
 
ADEMCO ONE YEAR LIMITED WARRANTY  
Alarm Device Manufacturing Company, a Division of Pittway Corporation, and its divisions, subsidiaries and affiliates ("Seller"),  
165 Eileen Way, Syosset, New York 11791, warrants its security equipment (the "product") to be free from defects in materials  
and workmanship for one year from date of original purchase, under normal use and service. Seller's obligation is limited to  
repairing or replacing, at its option, free of charge for parts, labor, or transportation, any product proven to be defective in  
materials or workmanship under normal use and service. Seller shall have no obligation under this warranty or otherwise if the  
product is altered or improperly repaired or serviced by anyone other than the Seller. In case of defect, contact the security  
professional who installed and maintains your security equipment or the Seller for product repair.  
This one year Limited Warranty is in lieu of all other express warranties, obligations or liabilities. THERE ARE NO EXPRESS  
WARRANTIES, WHICH EXTEND BEYOND THE FACE HEREOF. ANY IMPLIED WARRANTIES, OBLIGATIONS OR  
LIABILITIES MADE BY SELLER IN CONNECTION WITH THIS PRODUCT, INCLUDING ANY IMPLIED WARRANTY OF  
MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE, ARE LIMITED IN DURATION TO A  
PERIOD OF ONE YEAR FROM THE DATE OF ORIGINAL PURCHASE. ANY ACTION FOR BREACH OF ANY WARRANTY,  
INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY, MUST BE BROUGHT WITHIN 12  
MONTHS FROM DATE OF ORIGINAL PURCHASE. IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY  
CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR  
IMPLIED, OR UPON ANY OTHER BASIS OF LIABILITY WHATSOEVER, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY  
THE SELLER'S OWN NEGLIGENCE OR FAULT. Some states do not allow limitation on how long an implied warranty lasts or  
the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.  
Seller does not represent that the product may not be compromised or circumvented; that the product will prevent any  
personal injury or property loss by burglary, robbery, fire or otherwise; or that the product will in all cases provide adequate  
warning or protection. Buyer understands that a properly installed and maintained alarm may only reduce the risk of a burglary,  
robbery, fire or other events occurring without providing an alarm, but it is not insurance or a guarantee that such will not occur  
or that there will be no personal injury or property loss as a result. CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY  
FOR ANY PERSONAL INJURY, PROPERTY DAMAGE OR OTHER LOSS BASED ON A CLAIM THE PRODUCT FAILED TO  
GIVE WARNING. HOWEVER, IF SELLER IS HELD LIABLE, WHETHER DIRECTLY OR INDIRECTLY, FOR ANY LOSS OR  
DAMAGE ARISING UNDER THIS LIMITED WARRANTY OR OTHERWISE, REGARDLESS OF CAUSE OR ORIGIN,  
SELLER'S MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT, WHICH  
SHALL BE THE COMPLETE AND EXCLUSIVE REMEDY AGAINST SELLER. This warranty gives you specific legal rights,  
and you may also have other rights which vary from state to state. No increase or alteration, written or verbal, to this warranty  
is authorized.  
– 51 –  
 
®
ALARM DEVICE MANUFACTURING CO.  
A DIVISION OF PITTWAY CORPORATION  
165 Eileen Way, Syosset, New York 11791  
Copyright © 1997 PITTWAY CORPORATION  
N7527V2 6/97  
 

Techno Source Handheld Game System 40250 User Manual
Tiger Products Co Ltd Rice Cooker JAH A10A User Manual
Tokina Camera Lens TM22Z1022AI User Manual
Toshiba Electric Heater E STUDIO1355 User Manual
Toyota Automobile RAV 4 User Manual
Tripp Lite Surge Protector P036 002 User Manual
Troy Bilt Tiller 1634A User Manual
Tyco Printer FA 56100 User Manual
Vivotek Security Camera PT71373GPP ISMA User Manual
Weber Gas Grill Weber Genesis Silver B Gas Grill User Manual